HDFCFK

Pack contents:

4 x tubes of Ela-Stick Polymer adhesive, enough to bond 13 tread packs

HDFBTO

This pack is designed to clad a bullnose opening step.   The pack will clad any bullnose step up to 1150mm wide, 285mm deep and up to 200mm high.

Pack contents:

2 piece tread, 14mm solid oak with T&G jointing, curved to one end

Oak riser moulding kit; 2 x straight sections, 1 x curved section

Oak veneered curved riser board

HDFEB1O

1 solid oak extension board 1000mm wide, 142mm deep, 14mm thick, with Tongue & Groove profile

HDFBTO

This pack is designed to clad a bullnose opening step.   The pack will clad any bullnose step up to 1150mm wide, 285mm deep and up to 200mm high.

Pack contents:

2 piece tread, 14mm solid oak with T&G jointing, curved to one end

Oak riser moulding kit; 2 x straight sections, 1 x curved section

Oak veneered curved riser board

HDFSVO

The Oak String Veneer is supplied in a 285mm x 4200mm roll.  The Oak Veneer is fleece backed for strength and flexibility and is pre glued with a hot melt adhesive which means it is easily applied by using a hot iron.  The veneer is very thin and strong and can be cut to shape using sharp scissors with little effort.

HDFWTO

This pack is designed to clad a single winder step.  Most winders come in sets of 3 and you will need 3 winder packs to clad a full set.  The pack will clad any winder step up to 1200mm wide, 570mm deep and up to 200mm high.  The tread is designed to be trimmed to suit any of the three winder shapes seen in a typical set of 3 winders.

Pack contents:

4 piece tread, 14mm solid oak with T&G jointing.  Two longer sections for the front, and two shorter for the rear of the tread.

Oak riser moulding

Oak veneered riser board

Our Oak Stair Parts are available to order online, or in person, at our Sheffield showroom.  For more information give us a call on 0114 2449006 or Get in touch for more information.

Terms & Conditions

1. All items must be paid for in full at the time of ordering
2. Before you purchase it is advisable to visit our showroom and view our products if this is not possible it may be better to order one item to make sure that it is what you require - this will avoid costly return
3. Doors made to customers specification must be paid for in advance and will not be refunded unless faulty or damaged
4. We highly recommend you do not book fitters until your order has been received and checked.
5. Please make sure you check products for defects when they are delivered.   
6. Do not try to install any defective product. If a product has been installed we will assume that it was checked, as recommended, and deemed fit-for-purpose.
7. Cancelation of non stock items prior to delivery are subject to a 25% restocking charge when ordered in store
8. We reserve the right to refuse the return of any correctly supplied goods that have been ordered by the customer in store
9. Refunds willl not be made until the items have been returned to us and inspected 
10.  It is important with deliveries to try and accept goods when the courier is in your area if not this can mean delays out of our control. Some courier companies will only deliver to the kerb if this is not suitable please state at the point of order so a solution may be organised
11. The cost  returns is down to the customer unless goods are damaged/faulty at the time of delivery a responsable person must be present to inspect and sign for the goods as damage will not be accepted after the courier has left
12. Any correspondence regarding the return of goods or refunds must be done via email when ever possible if an email address is not available then via telephone or letter - distance contract must use the PDF form to cancel
13. If goods are noticed to be damaged on delivery please refuse them and return them via the courier this will stop any returns charge being made 
14. It is important to inspect the doors prior to your joiner arriving to fit them. In the event of there being damage that can not be seen through the packaging or a mistake on the door size. This will save any un necessary charges from your joiners if they are unable to do the job.
15. All timber products must be stored flat and in a dry environment
16. All doors either Internal or External are Engineered - This means that the doors are over veneered and that the internal structure will be made up of mixed species - special care must be taken when treating engineered doors and we stress that Varnish/ Water based products/Oils/Wax or Wood preservatives are not suitable for use on these doors - If in doubt what to use please contact our in house decorator
17. All timber products must be treated prior to hanging with an oil based high performance wood stain eg Sikkens  – varnish (Not suitable for some External Doors Please read manufacturers recommendations) – primer – base coat–top coat to the Recommended level i.e. internal doors minimum of 2 coats and external 4 coats with the final application applied after fitting All cut outs hinges – lock and letter boxes including top & bottoms of doors must be treated with the same amount
18. Engineered doors must not be treated with Danish Oil or anything similar
19. When treating External doors with clear stain it can lead to discolouration as there are either very low or no u values in these products. Manufacturers will not guarantee their doors if this is used.
20. It is recommended that pre-glazed external doors after hanging have clear silicone run round the edge of the glass both inside and out
21. All doors must be thoroughly inspected prior to treatment or hanging of both wood and glass as a refund for products or joiners fees will not be made
22. Wood can vary in colour and grain depending on batches
23. Doors should not be hung where there are freshly plastered walls or where plastering is going to take place after hanging
24. Before fitting it is recommended that the instruction affixed to the door be read carefully
25. Any pre-finished door will lose its guarantee if the finish is removed and not retreated
26. ANY PURCHASES MADE OVER THE TELEPHONE WILL NEED TO BE VERIFIED BY PRODUCTION OF THE CARD USED PLUS A UTILITY BILL ON DELIVERY OR COLLECTION